WORK ORDER FORM

RUTT'S MACHINE SHOP, INC.
300 Jonlyn Drive, Elizabethtown, PA 17022-9793

717-367-3011
Customer: Date: Make: Model:
Address: P.O.# Year: Disp.:
City:                         State: Ph. #                                    Job #:                            Eng. #:
Qty.

SHOP OPERATIONS

checkmark icon

Price

  
  ENGINE - Recondition As Needed      
  Disassemble      
  Assemble      
  BLOCK - Recondition As Needed      
*Please supply Main bolt Torque                                Ft. Lbs.
  Clean & Magnaflux Block

Remove Cam Brgs. & Freeze & Oil Plugs

      
  (Check / Line Hone / Bore) Main Bearing Housing Bores      
  (Spray Weld/ Knurl) To Tighten Main Caps      
  (Check/ Resurface/ Square Deck) Block      
  (Check/ Bore & Hone) Cyls. (                    )      
  (Rigid/ Flex) Hone Cyls. For New Rings      
  Bore & Install Repair Sleeve      
  Remachine Counterbores       
  (Remove/ Measure & Install) Cylinder Sleeves      
  Pressure Test Block      
 

Final
Clean And

 Install Cam Brgs.      
  Install (Freeze/ Oil) Plugs      
            
  CRANK - Recondition As Needed      
  Clean & Mag. Crank      
  R&R Oil Plugs & Clean Oil Galleries      
  Check Shaft & Call      
  Polish Rod (         ) Main (             ) Journals      
  Regrind Rod Journals (                            )      
  Regrind Main Journals (                            )      
  Weld To Build-Up Rod Journal      
  Weld To Build-Up Main Journal      
  Weld To Build-Up Seal Surface      
  Weld To Build-Up Thrust      
  Stress Relieve In Oven      
  Blast Crank      
  Straighten Crank      
  Balance Crank Assembly      
         
  Clean Mag & Check Camshaft      
         
Qty.

SHOP OPERATIONS

checkmark icon>

Price

  
  PISTONS - Clean & Blast      
  Remove, Clean, & Install Pistons Onto Rods      
  Check Pistons      
  RODS - Recondition As Needed      
 * Please Supply Rod Bolt Torque                     Ft. Lbs.
 * Install New Rod Bolts                                    Yes____________   No____________
  Clean & Magnaflux Rods      
  Check (Large End/ Pin End)      
  Check Alignment & Adjust      
  Recondition Large End & Check Alignment      
  Rebush, Bore C To C, Fit & Check Alignment      
         
  HEADS - Recondition As Needed      
  Basic Valve Job & Replace Freeze Plugs      
 

Included
With
Basic
Valve
Jobe

 Disassemble/ Assemble Heads      
  Clean, Mag., & Remove Gaskets      
  Mic, Polish, Grind, Butt Valves      
  Machine Seats & Vacuum Test      
  Machine Seats to Min. Spec. (Int. /  Ex.)      
  (Check/ Average-Out) Valve Recession (Int. / Ex.)      
  (Check/ Replace/ Knurl) Guides & Fit As Needed      
  Bore & Install Guides & Fit As Needed      
  Bore & Install Valve Seats As Needed      
  Pull Seats & Install New, As Needed      
  (Check/ Resurface) Head(s) As Needed      
  Remove Broken (Bolts/ Studs) & Heli-Coil      
  Resurface Rocker Arms      
  Replace Injector Tubes      
  Pressure Test      
  Repair Cracks      
         

Note: Send All Valves For Guide Fitting & Seat Work
         
  MANIFOLD(S) - (Clean/ Resurface)      
  FLYWHEEL - Resurface      
         
  TOTAL LABOR       
I authorize the above work to be done. Customer Signature _____________________________________